A molded part’s geometry affects how its mold is built, how efficiently it can be manufactured, and how consistently finished parts meet dimensional and quality requirements.
Reviewing that geometry against established injection molding design guidelines before tooling begins can reduce the risk of costly modifications and production problems. This checklist covers the major features engineers should evaluate: wall thickness, draft angles, ribs, bosses, undercuts, gates, and tolerances.
The dimensions provided are general starting points, not universal manufacturing limits. Final specifications should be reviewed against the selected resin, part function, mold design, and processing requirements.
1. Wall Thickness
Consistent wall thickness is one of the most important considerations in injection molding design.
Thermoplastics shrink as they cool. When sections of a part have significantly different wall thicknesses, they cool at different rates, increasing the risk of sink marks, internal voids, warpage, and dimensional variation.
Thicker sections may also require longer cooling times, increasing the overall molding cycle.
Use these guidelines when developing part geometry:
- Maintain consistent wall thickness. For many injection-molded thermoplastic parts, approximately 0.040–0.150 in (1–4 mm) is a common starting range. The appropriate thickness depends on the resin, part geometry, and application.
- Use gradual transitions. Where thickness must change, avoid abrupt steps that create uneven cooling or localized material buildup.
- Core out thick sections. Hollow bosses, ribs, and other structural features can provide stiffness without creating unnecessarily thick areas.
- Consider flow length. Long, thin sections may be difficult to fill, particularly with higher-viscosity materials or restrictive gate arrangements.
The objective is not simply to make every wall thinner. Wall thickness must support the part’s mechanical, dimensional, and functional requirements while remaining practical to mold.
2. Draft Angles
Draft is a slight taper applied to surfaces parallel to the mold’s opening direction.
It helps molded parts release from the tool without excessive friction, dragging, surface damage, or ejection force.
Draft requirements depend on the material, depth of the feature, surface finish, and overall geometry.
Common starting guidelines include:
- General surfaces: Start with approximately 1–2 degrees of draft per side for typical molded features.
- Shallow, smooth features: Lower angles, sometimes around 0.5 degrees, may be feasible depending on geometry and material.
- Deep features: Additional draft may be needed as draw depth increases.
- Textured surfaces: Provide additional draft based on the texture depth and surface specification.
- Ribs, bosses, and internal walls: Include draft where required for reliable mold release.
Draft should be considered early in CAD development rather than added after the geometry has been finalized.
For deep or textured features, confirm the required angles with the mold designer before releasing the part for tooling.
3. Ribs, Bosses, and Corners
Ribs and bosses provide structural support and fastening features without requiring thick solid sections throughout the part.
However, oversized ribs and bosses can create localized material buildup, increasing the likelihood of sink marks, voids, and warpage.
These features should be sized relative to the nominal wall thickness.
Starting Guidelines for Ribs and Bosses
The following values are general starting recommendations. Actual requirements depend on resin, geometry, loading, and cosmetic expectations.
| Feature | Starting guideline |
| Rib thickness at base | Approximately 40–60% of nominal wall thickness |
| Rib height | Keep as short as practical; around 3× rib thickness is a common starting limit |
| Rib spacing | Approximately 2× nominal wall thickness or more, where practical |
| Boss wall thickness | Approximately 60% of nominal wall thickness |
| Boss outside diameter | Often around 2× hole diameter, depending on fastener requirements |
| Inside corner radius | Approximately 0.5× nominal wall thickness or greater |
| Outside corner radius | Approximately inside radius + nominal wall thickness |
These dimensions should be adjusted when required for structural performance, material behavior, or manufacturing feasibility.
Rib Design
Ribs increase stiffness without adding thickness across the entire part.
To reduce molding defects:
- Keep ribs thinner than the wall they support.
- Avoid unnecessarily tall ribs that may complicate filling and ejection.
- Provide appropriate spacing between adjacent ribs.
- Include sufficient draft for mold release.
Boss Design
Bosses are commonly used for fastening, alignment, and assembly.
Core out bosses where possible to prevent excessive material buildup. Tall bosses may need reinforcing ribs or gussets to provide additional support.
Avoid placing thick boss features directly behind cosmetic surfaces when possible, since localized shrinkage may create visible sink marks.
Corner Design
Rounded corners promote smoother resin flow and reduce localized stress concentrations.
Sharp internal corners can create stress concentrations and make uniform wall thickness more difficult to maintain.
Use appropriate inside and outside radii while preserving the part’s dimensional and functional requirements.
4. Undercuts, Holes, and Threads
An undercut is a feature that prevents a molded part from releasing directly along the mold’s opening direction.
Examples include certain side holes, snap-fit features, recessed latches, and threaded details.
Depending on the geometry, undercuts may require slides, lifters, unscrewing cores, or other specialized tooling. These mechanisms can increase mold complexity, manufacturing cost, maintenance, and sometimes cycle time.
Not every undercut requires a moving component. Some can be produced using shutoffs, alternative parting-line arrangements, or other tooling methods.
Before finalizing the design, evaluate the following:
- Review the need for each undercut. Determine whether the feature can be redesigned, repositioned, or eliminated.
- Consider shutoffs or pass-through features. Some snap hooks and side openings can be formed using the main mold halves rather than additional moving components.
- Orient holes with the mold opening direction. Where part function allows, this can simplify tooling.
- Limit unsupported core-pin length. Long, slender pins are more susceptible to deflection and damage. The appropriate length-to-diameter ratio depends on the tooling design and molding conditions.
- Evaluate fastening options. Compare molded threads, screws designed for plastic, and threaded inserts based on joint strength, assembly requirements, and cost.
Threaded inserts can provide durable fastening points, particularly for components that require repeated assembly and disassembly. However, joint performance depends on the resin, insert design, installation method, and loading conditions.
5. Gates, Parting Lines, Ejection, and Tolerances
Part geometry influences where the mold can be gated, how the mold halves separate, and how the finished part is ejected.
These decisions should be considered during DFM review rather than after tooling begins.
LeVic’s in-house mold design and tooling capabilities support the evaluation of mold construction, manufacturability, and production requirements.
Gate Location
Gate location determines how molten resin enters and fills the cavity.
For many part geometries, directing flow from thicker sections toward thinner sections can improve filling and packing. However, the optimal gate position depends on material properties, flow length, part geometry, and cosmetic requirements.
Identify critical appearance surfaces so gate vestiges can be positioned appropriately. Gate placement also affects weld lines, air traps, and the way material flows around internal features.
Weld and Knit Lines
Weld or knit lines form where separate melt fronts meet during filling.
Depending on resin properties and processing conditions, these areas may have reduced local strength or different cosmetic characteristics.
Where possible, keep weld lines away from critical load-bearing features, snap fits, sealing surfaces, and other highly stressed areas.
Parting Lines
The parting line is where the mold halves meet.
Simple parting-line arrangements are generally easier to manufacture and maintain than complex configurations.
Parting lines may also leave a visible witness mark on the finished part, so their location should be evaluated against appearance and assembly requirements.
Ejection
Ejector pins and other ejection mechanisms apply force to remove the molded part from the tool.
Provide suitable areas for ejector contact, preferably on non-cosmetic surfaces.
Thin or poorly supported areas may deform or become damaged during ejection, particularly when the part has insufficient draft or remains tightly engaged with the core.
Dimensional Tolerances
Injection-molded dimensions vary based on resin shrinkage, part geometry, tooling, processing conditions, and measurement requirements.
Unnecessarily tight tolerances can increase tooling complexity, inspection requirements, and manufacturing costs.
Apply tighter tolerances to features that perform critical functions, such as mating, sealing, alignment, and assembly.
Use appropriate commercial tolerances for noncritical dimensions.
Material Selection
Select the resin before finalizing the part geometry whenever possible.
Different thermoplastics have different shrinkage characteristics, flow behavior, stiffness, thermal performance, and processing requirements.
These properties can influence wall thickness, draft, rib dimensions, gating, and dimensional stability.
Injection Molding DFM Checklist
Use this checklist before releasing a part design for quotation or tooling.
Material and Wall Thickness
- Resin selected based on functional and environmental requirements
- Recommended wall-thickness range reviewed for the selected material
- Nominal walls kept as uniform as practical
- Abrupt wall-thickness transitions minimized
- Thick sections cored out where appropriate
- Flow length and minimum wall thickness reviewed for mold filling
Draft and Part Release
- Draft applied to surfaces requiring it for mold release
- Additional draft evaluated for deep or textured features
- Internal ribs and bosses reviewed for draft
- Ejection surfaces identified and evaluated
Ribs, Bosses, and Corners
- Rib thickness reviewed relative to nominal wall thickness
- Rib height and spacing evaluated for strength and manufacturability
- Bosses cored out where possible
- Tall bosses supported with ribs or gussets where needed
- Cosmetic surfaces evaluated for potential sink marks
- Inside and outside corners appropriately radiused
Undercuts and Fastening
- Undercuts reviewed for elimination or simplification
- Shutoffs or alternative tooling arrangements considered where appropriate
- Holes oriented with the mold opening direction where practical
- Core-pin dimensions reviewed for tooling feasibility
- Threaded fastening requirements defined
- Insert options evaluated where applicable
Gating, Tolerances, and Production
- Preferred and restricted gate locations identified
- Cosmetic surfaces and finish requirements specified
- Critical weld-line locations evaluated
- Parting-line preferences communicated
- Ejector locations reviewed
- Tight tolerances limited to functional dimensions where practical
- Annual production volume and anticipated program life documented
Completing this review before tooling begins can help identify potential molding issues and reduce the likelihood of expensive modifications later.
Frequently Asked Questions
What Is the Most Important Injection Molding Design Rule?
Maintaining consistent wall thickness is one of the most important principles. It promotes more uniform cooling and helps control sink marks, warpage, cycle time, and dimensional variation. However, material selection, draft, and tooling requirements are also essential to a successful design.
How Much Draft Does an Injection-Molded Part Need?
Approximately 1–2 degrees per side is a common starting point for many molded surfaces. Lower angles may be feasible for certain shallow, smooth features, while deep or textured surfaces often require more draft. Final requirements depend on resin and geometry.
How Thick Should Injection-Molded Ribs Be?
A common starting guideline is approximately 40–60% of the nominal wall thickness. Thicker ribs may increase the risk of sink marks on the opposite surface. Final dimensions depend on material, structural loading, and cosmetic requirements.
When Should DFM Review Happen?
DFM should begin during the concept and CAD design stages and be revisited before the tooling RFQ is finalized.
Design changes are generally faster and less expensive before the mold is manufactured. An early review also gives the mold designer an opportunity to recommend changes that improve manufacturability.
Does DFM Affect Injection Molding Cost?
Yes. Features such as undercuts, thick walls, tight tolerances, and complex gating arrangements can increase tooling and production expenses.
A DFM review helps identify opportunities to simplify tooling and improve manufacturing efficiency.
For more information, see our guide to injection molding cost and the factors that drive tooling price
Get a DFM review from LeVic
LeVic engineers review every new part for manufacturability in SolidWorks and Mastercam before tooling begins. We design and build aluminum and steel molds in-house, mold on 55 to 250 ton presses, and hold tolerances down to ±0.001 in where the part requires it. Our quality systems are ISO 9001:2015 and AS9100D certified.
Send your STEP files and drawings for a mold design and DFM review.